-
sameerdentist posted an update 7 months ago
is there recommendation for simple study materials for bone graft and implant prosthetic part?
implantninja and anurag2 Comments-
Sure man! Have you taken a look at the little book of implant wisdom or the Implant Restoration 101 course?
-
thanks doctor i will see them
-
-
jorbrown posted an update 7 months ago
Patient had biomet 3I implant placed elsewhere. Had a cement retained crown #10. Its now completely covered by soft tissue. Any tips for removal of the screw?
View more comments-
I’ve seen Dr Huss vibrate out stuck screws with a cavitron
3 -
Yep, what Nathaniel sad can definitely help. Also Salvin makes a decent screw removal kit that has a bunch of goodies that can help. It’s always a pain in the butt but typically the screw comes out. Good luck!
1 - View more comments
-
-
Benjamin posted an update 7 months ago
First freehand implant placed a couple of weeks ago. #4. Felt my initial angulation was coming too far mesially and tried to course correct best I could. Happy with the final placement. A little tricky with the distal sloping of the ridge from #5 down to implant #3. Did a papilla sparing incision and tucked the tissue to the buccal with…
-
nicely done
-
-
Benjamin posted an update 7 months ago
First three career implants placed last month! Fully guided.
Some thoughts and questions:
The tissue punch for #29 probably left a less than ideal amount of buccal keratinized gingiva. One month later, patient has some irritation of the gingiva buccal to the healing abutment. In retrospect, I would have liked to flap rather than punch and try…
-
rez posted an update 7 months ago
HI Guys
i am a bit confused on PRF & CGF (sticky bone),mostly the RPM & time to prepare for sticky bone.
I understand A-PRF (PRF membrane) is 1300 rpm at 8 minutes (red tube), is the CGF (sicky bone0 is i-PRF which is red tube at 7oo RPM for 3 minutes then mixed with allograft? I understand each centrifuge has its own settings!
Can someone…
-
Hey! There’s a lot of info out there so it can get a bit confusing with all the different protocols. each centrifuge does have its own settings, which can make things tricky.
For A-PRF (membrane), I use 1300 rpm for 8 minutes with a red tube. For CGF (sticky bone), you’re on the right track! Usually, i-PRF is prepared at 700 rpm for 3… Read more
2
-
-
Can posted an update 8 months ago
Hi guys, I have a problem with an implant that I placed three months ago. bone was good, my torque 45 nm, the patient does not smoke, what could be the cause of this situation
-
two things to possibly consider if you see bone loss before loading.
1.) possible over-torquing or compression necrosis during placement
2.) overheating of bone during prep
of course a third option..
3.) some other factor we dont know and havent considered (i know real helpful right?)
probably/maybe 1 of first two but very difficult to know…
2 -
Any other medical conditions or medications to consider?
-
-
Aman posted an update 8 months ago
Anyone have any recommendations for a universal implant driver? Tryna make a universal kit
-
There are a lot out there now! You can actually find a kit on amazon even. https://amzn.to/4fXkPGh
-
-
87madrigal posted an update 8 months ago
Posterior implant placement with a surgical guide: a case that highlighted the value of precision, even in favorable conditions.
This patient had abundant posterior bone, which made planning and execution straightforward but no less important. Here are the lessons reinforced during this case:
1. Guided Surgery Refines Precision: Even with…
View more comments-
Very clean work and great documentation. 👊
-
I usually save guides for more “tricky” cases. But I also don’t have the best workflow at my office on getting them since the previous docs never did guided. I think I’ll be incorporating more as time goes.
- View 1 reply
- View more comments
-
-
Amy replied to the discussion Vertical grafting or not? in the forum Implant Tx Planning 8 months ago
Reply to Vertical grafting or not?
I agree. You should be good if the implant has enough bone support. However, I would mention the deficient gum support to the patient and show him/her with visuals, then document in your notes that options were given about potential outcomes down the way.
-
Dr. replied to the discussion Prolia and medical hx in the forum Implant Tx Planning 8 months ago
Reply to Prolia and medical hx
Thanks everyone for your input
- Load More
